Donji video pokazuje kako da instalirate aplikaciju na početni ekran svog uređaja.
Napomena: This feature may not be available in some browsers.
Pa brate lanac i spanere sam zamenio nisam ni 10k proso
- Engine Timing– If the camshaft(s) are no longer synced to the crank properly (such as if the timing chain jumped a tooth), it can cause the engine timing to be off enough to throw the P0011 even though it’s not the Actuator’s fault. Here’s more on that from this site: Timing Chain Jumped Symptoms and Diagnosis
- Engine Oil– If the engine oil is dirty or low, it may cause the actuator to function improperly. Also, the oil viscosity can be off
- Bad Intake Camshaft Position Actuator Solenoid– The actuator solenoid itself can go bad over time. You certainly don’t want to start here, since a lot of the time it’ll be something else that causes the P0011 to appear. Here’s a good video of someone replacing one, so you can see what goes into it.
- Wiring Issues– The wiring going from the solenoid to the ECM can become damaged or broken. This will throw the P0011 OBDII code. The wiring harness to the intake camshaft position sensor may also develop a poor connection. YouTube: How to Find an Open or Short the Fast Easy Way.
- Bad ECM (highly unlikely)- If the A4’s computer goes bad, then it may throw this code along with other issues. Here’s how to tell if you have a bad
Kad napise na Google P0011 izbacuje taj senzor kako ljudi menjaju i slike njega
- Engine Timing– If the camshaft(s) are no longer synced to the crank properly (such as if the timing chain jumped a tooth), it can cause the engine timing to be off enough to throw the P0011 even though it’s not the Actuator’s fault. Here’s more on that from this site: Timing Chain Jumped Symptoms and Diagnosis
- Engine Oil– If the engine oil is dirty or low, it may cause the actuator to function improperly. Also, the oil viscosity can be off
- Bad Intake Camshaft Position Actuator Solenoid– The actuator solenoid itself can go bad over time. You certainly don’t want to start here, since a lot of the time it’ll be something else that causes the P0011 to appear. Here’s a good video of someone replacing one, so you can see what goes into it.
- Wiring Issues– The wiring going from the solenoid to the ECM can become damaged or broken. This will throw the P0011 OBDII code. The wiring harness to the intake camshaft position sensor may also develop a poor connection. YouTube: How to Find an Open or Short the Fast Easy Way.
- Bad ECM (highly unlikely)- If the A4’s computer goes bad, then it may throw this code along with other issues. Here’s how to tell if you have a bad
Koliko kosta proveraNek ti neko izmeri signal ko se razume u te stvari pa onda kupuj i menjaj ako je to
Verovatno ali je bolje proveriti ima on svoje impulse koje šalje nzn tačno za tog ali može da se nađe ali ko se bavi tim može da izmeri da budes siguran....Kad napise na Google P0011 izbacuje taj senzor kako ljudi menjaju i slike njega
Koliko kosta otprilikeVerovatno ali je bolje proveriti ima on svoje impulse koje šalje nzn tačno za tog ali može da se nađe ali ko se bavi tim može da izmeri da budes siguran....
Nzn nije to nešto strašno.. Ne živim ja dole 10min nu treba .. Mozdes i da ga spojis na žicama na 12v ali ne non stop nego da mu das impuls tj samo dodirnes plus na bateriji sa žicom da otvori i nasprprocas spej za čišćenje Egr ili za Map sesora tako par puta videćeš kako se otvara .. Mozda je mehanička graška tj možda je zapekaoKoliko kosta provera
Danas sam stavio na dijagnostiku ima opet tu gresku P0011 I novu P0106 to je valjda map senzor, jedva ga palim sadNzn nije to nešto strašno.. Ne živim ja dole 10min nu treba .. Mozdes i da ga spojis na žicama na 12v ali ne non stop nego da mu das impuls tj samo dodirnes plus na bateriji sa žicom da otvori i nasprprocas spej za čišćenje Egr ili za Map sesora tako par puta videćeš kako se otvara .. Mozda je mehanička graška tj možda je zapekao
Moze WD?To ti je lancano.. Meni je otišao MAP sesor pa mi je upalio 4greske.. Izbrišes sve pa čekaš dok se prva ne upali tsko ja radim .. Imaš sprej za čišćenje probaj.. Dve žice spoji i vidi dal otvara i sprcaj
Moze WD?
Dobro brate hvala ti puno, javim sutra sta sam uradioNešto jače.. Imas nekog ko ima garažu ne treba tog puno
. Pogledajte prilog 647008
Evo ovaj ga čistiDobro brate hvala ti puno, javim sutra sta sam uradio