Quantcast

Pomoć

Somlix

Obećava
Poruka
86
Potreban mi je senzor polozaja bregastog vratila za a4 B6 2.0 FSI
Ne mogu nigde da ga nadjem
 

Prilozi

  • 51CeCbPuzVL._AC_SX425_.jpg
    51CeCbPuzVL._AC_SX425_.jpg
    33,8 KB · pregledi: 3

igi192

Elita
Poruka
18.667
Znaci siguran si da je to?
Evo ti malo pa razmisli
Camshaft Position Actuators change the lift of the camshaft up to 25 degrees. They are hydraulic, which means that they use the vehicle’s engine oil to control lift. So, if you have low oil pressure or dirty oil, it can keep them from doing their job properly, and trigger P0011
 

igi192

Elita
Poruka
18.667
  • Engine Timing– If the camshaft(s) are no longer synced to the crank properly (such as if the timing chain jumped a tooth), it can cause the engine timing to be off enough to throw the P0011 even though it’s not the Actuator’s fault. Here’s more on that from this site: Timing Chain Jumped Symptoms and Diagnosis
  • Engine Oil– If the engine oil is dirty or low, it may cause the actuator to function improperly. Also, the oil viscosity can be off
  • Bad Intake Camshaft Position Actuator Solenoid– The actuator solenoid itself can go bad over time. You certainly don’t want to start here, since a lot of the time it’ll be something else that causes the P0011 to appear. Here’s a good video of someone replacing one, so you can see what goes into it.
  • Wiring Issues– The wiring going from the solenoid to the ECM can become damaged or broken. This will throw the P0011 OBDII code. The wiring harness to the intake camshaft position sensor may also develop a poor connection. YouTube: How to Find an Open or Short the Fast Easy Way.
  • Bad ECM (highly unlikely)- If the A4’s computer goes bad, then it may throw this code along with other issues. Here’s how to tell if you have a bad
 

Somlix

Obećava
Poruka
86
  • Engine Timing– If the camshaft(s) are no longer synced to the crank properly (such as if the timing chain jumped a tooth), it can cause the engine timing to be off enough to throw the P0011 even though it’s not the Actuator’s fault. Here’s more on that from this site: Timing Chain Jumped Symptoms and Diagnosis
  • Engine Oil– If the engine oil is dirty or low, it may cause the actuator to function improperly. Also, the oil viscosity can be off
  • Bad Intake Camshaft Position Actuator Solenoid– The actuator solenoid itself can go bad over time. You certainly don’t want to start here, since a lot of the time it’ll be something else that causes the P0011 to appear. Here’s a good video of someone replacing one, so you can see what goes into it.
  • Wiring Issues– The wiring going from the solenoid to the ECM can become damaged or broken. This will throw the P0011 OBDII code. The wiring harness to the intake camshaft position sensor may also develop a poor connection. YouTube: How to Find an Open or Short the Fast Easy Way.
  • Bad ECM (highly unlikely)- If the A4’s computer goes bad, then it may throw this code along with other issues. Here’s how to tell if you have a bad
Pa brate lanac i spanere sam zamenio nisam ni 10k proso
 

Somlix

Obećava
Poruka
86
  • Engine Timing– If the camshaft(s) are no longer synced to the crank properly (such as if the timing chain jumped a tooth), it can cause the engine timing to be off enough to throw the P0011 even though it’s not the Actuator’s fault. Here’s more on that from this site: Timing Chain Jumped Symptoms and Diagnosis
  • Engine Oil– If the engine oil is dirty or low, it may cause the actuator to function improperly. Also, the oil viscosity can be off
  • Bad Intake Camshaft Position Actuator Solenoid– The actuator solenoid itself can go bad over time. You certainly don’t want to start here, since a lot of the time it’ll be something else that causes the P0011 to appear. Here’s a good video of someone replacing one, so you can see what goes into it.
  • Wiring Issues– The wiring going from the solenoid to the ECM can become damaged or broken. This will throw the P0011 OBDII code. The wiring harness to the intake camshaft position sensor may also develop a poor connection. YouTube: How to Find an Open or Short the Fast Easy Way.
  • Bad ECM (highly unlikely)- If the A4’s computer goes bad, then it may throw this code along with other issues. Here’s how to tell if you have a bad
Kad napise na Google P0011 izbacuje taj senzor kako ljudi menjaju i slike njega
 

igi192

Elita
Poruka
18.667
Koliko kosta provera
Nzn nije to nešto strašno.. Ne živim ja dole 10min nu treba .. Mozdes i da ga spojis na žicama na 12v ali ne non stop nego da mu das impuls tj samo dodirnes plus na bateriji sa žicom da otvori i nasprprocas spej za čišćenje Egr ili za Map sesora tako par puta videćeš kako se otvara .. Mozda je mehanička graška tj možda je zapekao
 

Somlix

Obećava
Poruka
86
Nzn nije to nešto strašno.. Ne živim ja dole 10min nu treba .. Mozdes i da ga spojis na žicama na 12v ali ne non stop nego da mu das impuls tj samo dodirnes plus na bateriji sa žicom da otvori i nasprprocas spej za čišćenje Egr ili za Map sesora tako par puta videćeš kako se otvara .. Mozda je mehanička graška tj možda je zapekao
Danas sam stavio na dijagnostiku ima opet tu gresku P0011 I novu P0106 to je valjda map senzor, jedva ga palim sad
 

igi192

Elita
Poruka
18.667
To ti je lancano.. Meni je otišao MAP sesor pa mi je upalio 4greske.. Izbrišes sve pa čekaš dok se prva ne upali tsko ja radim .. Imaš sprej za čišćenje probaj.. Dve žice spoji i vidi dal otvara i sprcaj
 

Top
  Blokirali ste reklame
Dragi prijatelju, nemojte da blokirate reklame - isključite Ad Blocker na Forumu, jer će tako mesto vaših susreta na Krstarici ostati besplatno za korišćenje.