Pomoc oko flesa

Pozdrav svima, imam jedan problem. Naime, kada sam ubacio usb fles u kompjuter iz neznatnog razloga mi je trazio da ga formatiram. Kada sam pokusao pisalo mi je da fles najvise moze imati 750MB nakon formatiranja, iako je u pocetku imao 16GB. Stvarno ne znam sta da radim i ne razumem se u ovakve stvari. Pomozite mi sto pre

ИМАШ ...УЉЕЗЕ...НА КОМПУ...

ОЧИСТИ ГА...

skeniraj komp, probaj na drugom, ili kupi nov flash

Zaboravih da napomenem. Problem je poceo od trenutka kada sam fles ubacio u digitalnu u nadi da cu na njega uspeti nesto da snimim. Posto sam ja tako pametan , kada mi je na TV-u izaslo da formatiram fles ja sam prihvatio. E onda je problem poceo na kompjuteru, ali i na lap topu

Mix123:

Zaboravih da napomenem. Problem je poceo od trenutka kada sam fles ubacio u digitalnu u nadi da cu na njega uspeti nesto da snimim. Posto sam ja tako pametan , kada mi je na TV-u izaslo da formatiram fles ja sam prihvatio. E onda je problem poceo na kompjuteru, ali i na lap topu

Kliknite za proširenje...

Probaj sa MCShield programom da preskeniras.Nije veliki program,a moze da pomogne.

Brate, meni se čini da se ta fleshka femka. Znaš šta da uradiš? Kupi još jednu fleshku, ali zapremniju. Od recimo 20 giga sine, i da ima neke besne šare, recimo neke munje i lobanje. I onda pre nego što ćeš istu ubacivati u otvore svojega kućišta i lapa, uvek prvo kinji ovu staru fleshku, govoreći joj da je prevazidjena, i na oči joj ubacuj ovu od 20 giga u komp. Pazi, uvek održavaj kontakt očima dok to radiš. Važno je. Poruka mora biti poslata.

Mix123:

Pozdrav svima, imam jedan problem. Naime, kada sam ubacio usb fles u kompjuter iz neznatnog razloga mi je trazio da ga formatiram. Kada sam pokusao pisalo mi je da fles najvise moze imati 750MB nakon formatiranja, iako je u pocetku imao 16GB. Stvarno ne znam sta da radim i ne razumem se u ovakve stvari. Pomozite mi sto pre

Kliknite za proširenje...

Najverovatnije da nije crkao! Ako ne pokazuje pun kapacitet memorije, uradi sledeće (Vista/WIN7/8)

1) Type "DISKPART" from the Command Prompt (accessible by clicking on Start and then typing "cmd" into the open field); you will then see the following prompt: DISKPART>
2) Type "LIST DISK" to see what number your USB drive is listed as.
3) Type "SELECT DISK 2" (if your USB is disk 2; replace # with your disk #); Diskpart will confirm that "Disk 2 is now the select disk."
4) Type "SELECT PARTITION 1" (this command selects what should be the only partition on your USB drive, the small one that you want to delete to get back the larger, full partition size). Diskpart will confirm with "Partition 1 is now the selected partition."
5) Type "DELETE PARTITION". This will delete the old partition. There are no warning prompts if you have existing data - make sure you have copied everything off before doing this!
6) Type "CREATE PARTITION PRIMARY" to create a new, full-size partition. Diskpart will confirm with message of "Diskpart succeeded in creating the specified partition." You can type in "LIST PARTITION" to confirm the new, full-size.
7) Type "EXIT" to leave Diskpart. You can now format your USB drive by using the standard Windows formatting process.

OvajOnaj:

Najverovatnije da nije crkao! Ako ne pokazuje pun kapacitet memorije, uradi sledeće (Vista/WIN7/8)

1) Type "DISKPART" from the Command Prompt (accessible by clicking on Start and then typing "cmd" into the open field); you will then see the following prompt: DISKPART>
2) Type "LIST DISK" to see what number your USB drive is listed as.
3) Type "SELECT DISK 2" (if your USB is disk 2; replace # with your disk #); Diskpart will confirm that "Disk 2 is now the select disk."
4) Type "SELECT PARTITION 1" (this command selects what should be the only partition on your USB drive, the small one that you want to delete to get back the larger, full partition size). Diskpart will confirm with "Partition 1 is now the selected partition."
5) Type "DELETE PARTITION". This will delete the old partition. There are no warning prompts if you have existing data - make sure you have copied everything off before doing this!
6) Type "CREATE PARTITION PRIMARY" to create a new, full-size partition. Diskpart will confirm with message of "Diskpart succeeded in creating the specified partition." You can type in "LIST PARTITION" to confirm the new, full-size.
7) Type "EXIT" to leave Diskpart. You can now format your USB drive by using the standard Windows formatting process.

Kliknite za proširenje...

HVALA TI MNOGOOOO!!! USPEO SAM I FLES MI JE OPET KAO NOV <3